Air Knives
Airmasters Energy Saving Air Curtain also known as “Air Knives” provides an efficient laminar sheet of air for wide area cleaning and drying applications. Since Air Knives are a type of air amplifiers, they use a small amount of compressed air to deliver a powerful, high velocity, laminar sheet of air over wide areas such as moving webs, film, sheets, strips, auto bodies and other large assemblies and objects. Airmasters Air Knives are the perfect replacements for drilled or slotted lengths of pipe. In addition, the Air Knives offers up to 70% compressed air savings when compared to the drilled pipes.
Stainless Steel models are ideal for food, pharmaceutical, chemical and other applications where purity, high temperatures or corrosive environments are concerned.
Airmaster Air Knives increase thrust and velocity, reduced noise, excellent uniformity, and significantly outperforms any competing, wide blowoff device.
Use of Shims
Airmaster uses ONLY stainless steel shims in their Air Knife products as plastic shims wear out over time and require replacement, even with relatively clean air systems. Stainless steel shims are .002” (.050 mm). In most application this is adequate. However, velocity and force can be increased approximately 30% by adding a second .002” (.050 mm) shim. Shims may be stacked up to 5 sets. If using three or more sets however, the air inlets at the “ends” should be used to maintain even flow
along the Air Knife system. Otherwise a slight d op in pressure and flow will occur across from the rear inlet ports if they are usedwith three or more shims Note that noise levels and air use will go up with an increased number of shims.
Additional information
| Features | Innovative design High Air Flow Amplification Full Flow – Air across entire length of Air Knife Instant On / Off, No electricity or explosion hazard |
|---|---|
| 2TEST | asxasxasx |
Related products
-
High Force Air Blowgun (HFAG)
<div class="airmaster"> <p>High Force (HFAG) Blowguns offered by us are rugged and ergonomic, ideal for Blow-off applications in a variety of Industries.</p> <p>The AIRMASTERS compressed air gun with high blowing force is widely used in industry for cleaning, drying and cooling in particular applications, where a traditional blow gun is insufficient and where a greater blowing force is needed.</p> <p>The AIRMASTERS compressed air gun with high blowing force is the low cost, lightweight, high power and low noise air gun.</p> </div> <div class="trial-btn"> <a type="button" class="trigger">Ask For Trial</a> </div> <div class="modal"> <div class="modal-content"> <span class="close-button">×</span> [contact-form-7 id="c82d8b4" title="Product Enquiry"] </div> </div>Read more -
Adjustable Air Amplifiers
<div class="airmaster"> Adjustable Air amplifier takes energy from a small volume of compressed air to produce a high velocity, high volume, low pressure output air flow. It is easy to mount and maintains reducing both compressed air consumption and noise levels. Adjustable Air Amplifiers don’t come with Shims, they are manually adjustable with the help of a lock ring. The lock ring can adjust the air flow of the air amplifier, which can help to control the vacuum generated and the air blow off. </div> <div class="trial-btn"><a class="trigger" href="https://www.agency09.co/staging/aceflow/wp-content/uploads/2024/02/Adjustable-Air-Amplifier.pdf" type="button">Download Brochure</a></div>Read more -
Air Flow Blade / Air Wipe System
<div class="airmaster"> The Air Wipe System produces a “laminar” Flow of air along its 360º angle using the “Coanda” effect which “entrains” a large volume of air from the surrounding area along with the small amount of compressed air from the Ring-Blade Air Wipe System air-saver wiper-blade to produce an output flow up to 30 times. Pay back on compressed air savings can be as soon as a few weeks in some applications when compared to nozzle “rings” or simple annular slots used by other air wiping systems. Air Wipe Circular Air Knife blow off, clean, cool and dry cables, pipes, extrusions, hoses, wires and ropes. Air Wipe Circular Air Knife is easy to mount and maintain and reduces both compressed air consumption and noise levels.Air Wipe or Ring Blade - Circular Air Knife is available in aluminium or stainless steel 316L. Air Flow Blade Compressed Air Wipe Systems are available in 12 standard (inside) diameters: 3/8”, ½” 1", 2”, 3", 4", 5”, 6", 7”, 9”, 11”. Special diameters are also available on special request. Ring-Blade Compressed Air Wipe Systems come with a standard .002" outlet gap which will work for 90% of all applications encountered. If greater force is required, a second .004" shim may be installed to open the gap for greater flow. Material of construction: Coated Aluminium & Stainless Steel </div> <div class="trial-btn"><a class="trigger" href="https://www.agency09.co/staging/aceflow/wp-content/uploads/2024/02/Air_Flow_Blade_Air_Wipe_System.pdf" type="button">Download Brochure</a></div>Read more -
Machine Tool Cooling System
<div class="airmaster"> AIR-MTC tool coolers are used for dry machining applications - replaces polluting and often toxic mist systems to improve dry machining operations. No mess, no residue and low in cost.AIR-MTC tool coolers are made of durable stainless steel and the Vortex tubes inside of them, are also of stainless steel with brass generators. No pieces made of plastic! It can be used in high temperature environments. AIR-MTC tool coolers can improve dry machining operations and assist in pot cooling applications for a variety of industrial machining processes by increasing machining rates and extending tool life. AIR-MTC tool coolers can often replace costly mist coolants and certainly improves the quality and output of all types of dry machining operations form metals to plastics. Unit is low cost, no electricity, with no moving parts and is essentially maintenance free. The tool cooler is available in various capacities 15, 25, 30 and 40 in addition, there are two versions, a single exit point and double exit point system. Our tool coolers use a strong integrated magnetic base. We recommend using the inlet air-pressure of 5 to 7 Bar </div> <div class="trial-btn"><a class="trigger" href="https://www.agency09.co/staging/aceflow/wp-content/uploads/2024/02/Machine_Tool_Cooler.pdf" type="button">Download Brochure</a></div>Read more
