<div class="airmaster">
The AIRMASTERS+ compressed air knives are engineered to deliver high blowing strength while significantly reducing energy consumption and noise levels. Manufactured in Italy with precision machinery, these air knives ensure a uniform flow and consistent force distribution along the entire length. Utilizing the Coanda effect, AIRMASTERS+ air knives draw in a large volume of environmental air with a minimal amount of compressed air, achieving an impressive 1:50 air amplification ratio.
</div>
<div class="trial-btn"><a class="trigger" href="https://www.agency09.co/staging/aceflow/wp-content/uploads/2024/02/AIR-KNIFE.pdf" type="button">Download Brochure</a></div>
Read more
<div class="airmaster">
Airmasters Energy Saving Air Curtain also known as “Air Knives” provides an efficient laminar sheet of air for wide area cleaning and drying applications. Since Air Knives are a type of air amplifiers, they use a small amount of compressed air to deliver a powerful, high velocity, laminar sheet of air over wide areas such as moving webs, film, sheets, strips, auto bodies and other large assemblies and objects. Airmasters Air Knives are the perfect replacements for drilled or slotted lengths of pipe. In addition, the Air Knives offers up to 70% compressed air savings when compared to the drilled pipes.
Stainless Steel models are ideal for food, pharmaceutical, chemical and other applications where purity, high temperatures or corrosive environments are concerned.
Airmaster Air Knives increase thrust and velocity, reduced noise, excellent uniformity, and significantly outperforms any competing, wide blowoff device.
<h5>Use of Shims</h5>
Airmaster uses ONLY stainless steel shims in their Air Knife products as plastic shims wear out over time and require replacement, even with relatively clean air systems. Stainless steel shims are .002” (.050 mm). In most application this is adequate. However, velocity and force can be increased approximately 30% by adding a second .002” (.050 mm) shim. Shims may be stacked up to 5 sets. If using three or more sets however, the air inlets at the “ends” should be used to maintain even flow
along the Air Knife system. Otherwise a slight d op in pressure and flow will occur across from the rear inlet ports if they are usedwith three or more shims Note that noise levels and air use will go up with an increased number of shims.
</div>
<div class="trial-btn"><a class="trigger" href="https://www.agency09.co/staging/aceflow/wp-content/uploads/2024/02/AIR-KNIFE.pdf" type="button">Download Brochure</a></div>
Read more
<div class="airmaster">
<p>Airmasters Energy Saving Air Curtain also known as “Air Knives” provides an efficient laminar sheet of air for wide area cleaning and drying applications. Since Air Knives are a type of air amplifiers, they use a small amount of compressed air to deliver a powerful, high velocity, laminar sheet of air over wide areas such as moving webs, film, sheets, strips, auto bodies and other large assemblies and objects. Airmasters Air Knives are the perfect replacements for drilled or slotted lengths of pipe. In addition, the Air Knives offers up to 70% compressed air savings when compared to the drilled pipes.</p>
<p>Stainless Steel models are ideal for food, pharmaceutical, chemical and other applications where purity, high temperatures or corrosive environments are concerned.</p>
<p>Airmaster Air Knives increase thrust and velocity, reduced noise, excellent uniformity, and significantly outperforms any competing, wide blowoff device.</p>
</div>
<div class="trial-btn">
<a type="button" class="trigger" href="https://www.agency09.co/staging/aceflow/wp-content/uploads/2024/02/Panel_Cooler.pdf">Download Brochure</a>
</div>
Read more
<div class="airmaster">
AIR-MTC tool coolers are used for dry machining applications - replaces polluting and often toxic mist systems to improve dry machining operations. No mess, no residue and low in cost.AIR-MTC tool coolers are made of durable stainless steel and the Vortex tubes inside of them, are also of stainless steel with brass generators. No pieces made of plastic! It can be used in high temperature environments.
AIR-MTC tool coolers can improve dry machining operations and assist in pot cooling applications for a variety of industrial machining processes by increasing machining rates and extending tool life. AIR-MTC tool coolers can often replace costly mist coolants and certainly improves the quality and output of all types of dry machining operations form metals to plastics. Unit is low cost, no electricity, with no moving parts and is essentially maintenance free.
The tool cooler is available in various capacities 15, 25, 30 and 40 in addition, there are two versions, a single exit point and double exit point system. Our tool coolers use a strong integrated magnetic base. We recommend using the inlet air-pressure of 5 to 7 Bar
</div>
<div class="trial-btn"><a class="trigger" href="https://www.agency09.co/staging/aceflow/wp-content/uploads/2024/02/Machine_Tool_Cooler.pdf" type="button">Download Brochure</a></div>
Read more
